Designed to remove and tighten the wiper bezel nut 17512-1A and the headlight bezel nut 11650-1A into the dash without damaging the chrome. Machined from strong 6061 billet aluminum. This dedicated tool is made from solid billet aluminum with a red anodized finish. The design allows for the use of a 7/8 or 22mm wrench if needed.
Caution! Do not over-tighten! This may damage the tool and the bezel. Use firm pressure pushing the tool into the bezel while loosening or tightening with wrench. Hand tightening in most cases should be sufficient.
Note that this tool fits original light switch bezels. It does not work well on the current repro light bezels 11650-1A. Works perfectly on wiper bezel nuts whether original or our repro 17512-1A.
Ford Mustang Years:
1965 (65), 1966 (66)
Above years shown are used for searches and are not application listings.
Ford Bronco Years:
1966 (66), 1967 (67), 1968 (68), 1969 (69), 1970 (70), 1971 (71), 1972 (72), 1973 (73), 1974 (74), 1975 (75), 1976 (76), 1977 (77)
Above years shown are used for searches and are not application listings.
Chevrolet & GMC Truck Years:
1955 (55), 1956 (56), 1957 (57), 1958 (58), 1959 (59)
Above years shown are used for searches and are not application listings.
NPD Part Number : 930-1 Manufacturer Reference #'s: T-110-RD,
1965-1966 MUSTANG WIPER AND LIGHT SWITCH BEZELS ON DASH
1966-1966 BRONCO F-11650-4 HEADLIGHT BEZEL NUT
1968-1977 BRONCO F-11650-4 HEADLIGHT BEZEL NUT
1955-1955 CHEVY TRUCK 2ND SERIES, HEADLIGHT SWITCH RETAINING NUT
1956-1959 CHEVY TRUCK HEADLIGHT SWITCH RETAINING NUT
WARNING: This product can expose you to chemicals including lead and DEHP, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Works well, much better than trying to use a pair of needle-nose pliers.
Submitted on September 17, 2018 by Joseph S.
Quality
Value
Submitted on August 02, 2019 by Normand S.
YES I would recommend this product.
Quality
Value
it worked well on the light switch, but not so great on the wiper switch. I should have used a large screwdriver, but I thought this would have less of a chance of damaging the switch bezels. Save the money and use a large screwdriver, while being careful not to scratchup the bezels.
Submitted on August 14, 2019 by Marty T.
YES I would recommend this product.
Quality
Value
The tool worked perfect for removing the dash knob bezels on my 63 Ranchero.
Submitted on December 08, 2019 by David A.
YES I would recommend this product.
Quality
Value
Product did the job it was designed for but the metal was so soft it deformed and is now useless. Given the cost and shipping rate it was not a very good product. I realize the quality issue is not on NPD, but it was of poor quality non the less.
Submitted on May 31, 2021 by Leif P.
Quality
Value
Tool worked perfectly on the new aftermarket headlight switch nut on my 70 Cougar.
Submitted on January 08, 2022 by Stephen L.
YES I would recommend this product.
Quality
Value
Worked, but the ends didn’t hold up and rounded off making it very hard to use. So works on OEM nuts IF they are clean and oiled but if you are taking off the original nuts and they are stuck, the ends aren’t strong enough to not get damaged and then making the tool hard if not impossible to use.
Submitted on May 19, 2022 by Craig C.
Quality
Value
I'm sure this tool works on some models. I have a 66 Chevy C20 and it will not work on light or wiper bezel or the chock cable nut. It appears well made and the cost was fine, but the application was off.
Submitted on December 07, 2022 by Ed S.
Quality
Value
Exactly what I needed! This tool has came in handy over the years, whether it was used to replace the: wiper switch and harness, the light switch and harness, or simply used to polish the original bezel's, on my late '66 Coupe.
Submitted on March 23, 2024 by Blaine W.
YES I would recommend this product.
Quality
Value
In Stock!
