TORQUE BOX, Front, RH, Canadian made, .075 inch thick steel or 14 gauge, Torque boxes were first used on hardtops in 1967 on the LH side only, These will fit 67 they just were not original to that year, Note: While these panels are made in Canada and at one time part of the Paddock/American-Designers tooling, the quality of the parts have degraded over time to a point where we have a strong preference towards their imported counterpart,
NPD Part Number : 114-2RH Manufacturer Reference #'s: M114AR, C7ZZ-65016A22-C, C8ZZ-65103A28-A
1965-1967 MUSTANG COUPE, FASTBACK, CUSTOM ADDITION
1968-1970 MUSTANG COUPE, FASTBACK, RH
1967-1970 COUGAR COUPE, RH, CUSTOM ADDITION FOR 67
WARNING: This product can expose you to chemicals including lead and DEHP, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
It took a little trimming and a hour or so but it fit well.
Submitted on April 04, 2019 by John K.
YES I would recommend this product.
Quality
Value
It’s best that you separate and install in two separate pieces, had to do some fabrication to get to fit in my mustang
Submitted on September 04, 2019 by Mike B.
YES I would recommend this product.
Quality
Value
It was an okay piece. Many years ago I installed torque boxes on my 65 fastback and they fit like a glove but can not recall who made them. This took a little effort to get it to fit, more than I expected.
Submitted on November 17, 2019 by Robert M.
Quality
Value
These Canadian made torque boxes are well made. They do require some minor trimming so that they'll fit properly but it's very minor. It's a must that these torque boxes are welded in securely to be effective. I would definitely purchase these again.
Submitted on March 25, 2020 by Christopher T.
YES I would recommend this product.
Quality
Value
If you are installing this after the floor is in you will have fitment issues. There is some moderate trimming and fitting to install this but quality is good.
Submitted on June 06, 2020 by Peggy C.
YES I would recommend this product.
Quality
Value
Used pieces of this product to repair in place torque box. good materal to work with.
Submitted on July 31, 2020 by Paul D.
YES I would recommend this product.
Quality
Value
Damn good looking parts
Submitted on January 22, 2021 by Nicholas J.
YES I would recommend this product.
Quality
Value
Submitted on June 10, 2021 by Rita D.
Quality
Value
Looks to be made structurally sound, nice heavy gauge material
Submitted on July 16, 2021 by Andrew H.
YES I would recommend this product.
Quality
Value
Very good quality, fitment was perfect
Submitted on November 05, 2021 by Joseph M.
YES I would recommend this product.
Quality
Value
Had to split spotwelds as they would not align as one part. After taking apart an installing in two pieces fit like a glove
Submitted on December 01, 2021 by Dale b.
Quality
Value
This North American made, thicker steel is a quality piece worked well with the US Made, thicker steel floor pan that I used during the restoration of my '66 coupe. Very happy with all the SPI steel products that I have purchased through NPD.
Submitted on August 21, 2022 by Blaine W.
YES I would recommend this product.
Quality
Value
I researched this part on Mustang forums, and found the consensus that the part needs to be modified substantially. First remove all the spot welds, then cut to fit. Considering the application is for 65-68 and it was not standard on 65-66, these should be made to retrofit to those years, and sold in two pieces. Second, these are made to install assuming you have the floor pans removed, as the lip on the floorboard section is towards the rear of the car. If you are adding these to 65-66 cars and don't have the floorpans out, there is not way to weld the lip to the outer panel. It has to be bent 180 degrees to weld. The overall fit is way off. I had to trim about a 1/2" off the frame side to make it fit.
Submitted on June 13, 2023 by BRIAN H.
Quality
Value
In Stock!
