Polished billet aircraft aluminum. 6 hole mounting. Use with 3600-14A, 3600-14LB, 3623-14A.
Note: Installing custom steering wheels with steering column adapters may cause interference with the steering column tube. Adjusting the steering column tube for clearance may be necessary. 70-up vehicles will loose the steering wheel lock function.
Ford Mustang Years:
1968 (68), 1969 (69), 1970 (70), 1971 (71), 1972 (72), 1973 (73)
Above years shown are used for searches and are not application listings.
Mercury Cougar Years:
1968 (68), 1969 (69), 1970 (70), 1971 (71), 1972 (72), 1973 (73)
Above years shown are used for searches and are not application listings.
Ford Falcon and Ranchero Years:
1965 (65), 1966 (66), 1967 (67), 1968 (68), 1969 (69), 1970 (70)
Above years shown are used for searches and are not application listings.
Ford Fairlane and Ranchero Years:
1965 (65), 1966 (66), 1967 (67), 1968 (68), 1969 (69), 1970 (70)
Above years shown are used for searches and are not application listings.
Ford Torino and Ranchero Years:
1968 (68), 1969 (69), 1970 (70), 1971 (71)
Above years shown are used for searches and are not application listings.
Ford Truck F1, F2, F3, F100, F150, F250, F350, Expedition, Excursion, Lincoln Navigator and Blackwood Years:
1969 (69), 1978 (78), 1979 (79)
Above years shown are used for searches and are not application listings.
NPD Part Number : 3511-14D Manufacturer Reference #'s: S8MS-3511-P-6,
1968-1973 MUSTANG W/ 3600-14A & 14LB WHEEL, 70-73 WILL LOOSE THE STEERING WHEEL LOCK FUNCTION, W/ ALTERNATOR
1968-1973 COUGAR W/ 3600-14A & 14LB WHEEL, 70-73 WILL LOOSE THE STEERING WHEEL LOCK FUNCTION
1969-1969 F100-F350 W/ 3600-14A & 14LB WHEEL
1978-1979 F100-F350 W/ 3600-14A & 14LB WHEEL, WILL LOOSE THE STEERING WHEEL LOCK FUNCTION
1965-1967 MUSTANG W/ STEEROIDS OR IDIDIT STEERING COLUMNS, WILL NOT FIT FLAMING RIVER
1965-1970 FALCON (BEFORE 1/1/70), W/ STEEROIDS OR IDIDIT STEERING COLUMNS, WILL NOT FIT FLAMING RIVER
1970-1971 TORINO W/ STEEROIDS OR IDIDIT STEERING COLUMNS, WILL NOT FIT FLAMING RIVER
1970-1970 FALCON (FROM 1/1/70), W/ STEEROIDS OR IDIDIT STEERING COLUMNS, WILL NOT FIT FLAMING RIVER
1968-1969 TORINO W/ STEEROIDS OR IDIDIT STEERING COLUMNS, WILL NOT FIT FLAMING RIVER
1965-1969 FAIRLANE W/ STEEROIDS OR IDIDIT STEERING COLUMNS, WILL NOT FIT FLAMING RIVER
1970-1970 FAIRLANE W/ STEEROIDS OR IDIDIT STEERING COLUMNS, WILL NOT FIT FLAMING RIVER
WARNING: This product can expose you to chemicals including lead and DEHP, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
The adapter is recommend for Mustang 1965-1973. The design is not conducive with my 1970 Mustang steering column. The design has no tab hole for the ignition key locking cylinder. The locking steering wheel function is no longer functional. The electrical contact for the horn is non functional. Turn signal deactivation requires turning the steering wheel beyond 3/4 revolutions on return to wheels straight. The adapter might be considered for Mustang steering columns for the years before 1970. I don't have that installation experience. I would not recommend to Mustang owners 1970-1973.
Submitted on September 21, 2020 by Roz C.
Quality
Value
The steering wheel column adapter will work well for a 1969 Mustang with possible additions to the column required. Specifically, stacked tolerances between the installed location of the column bearing, spacer and c-clip may cause the adapter to bottom out on the column when tightening the column nut. If this occurs, the bottomed-out adapter puts stress on the spring-loaded horn commutator pins that are part of the plastic turn signal mechanism. In this condition, you may hear squeaking of the over-loaded horn pins contacting the adapter’s commutator ring and you will likely feel resistance when turning the wheel due to the adapter rubbing the column. Do not drive the car in this condition or you may break off the horn pin plastic mounts. Solution for 1969 Mustang is to install a thin wall spacer that contacts the c-clip within the column and stands the adapter off the base of the column. I cut down a few common copper pipe plumbing reducers until I achieved a 0.050” gap between the adapter and column base. 0.035” would probably be optimum but its hard to control the cut of the copper pipe spacer and you don’t want to knock it down on the bench grinder or it won’t be flat, so try a few times. Turn signal activation is easier than it seems. The two roll pins with the adapter are NOT required for 1969 Mustang. Simply position one of the two notches to engage the turn signal pin on the turn signal switch in the nominal steering wheel centered position which is about 7 o’clock. This is just like the stock Ford wheel which has a notch on the wheel hub. If you cannot center your wheel with the turn signal switch pin in the approximate 7 o’clock position, you may try rotating the wheel adapter 1 spline in either direction, however that will likely bias the turn signal cancellation to cancel early in one direction and late in the other. It’s more desirable to get the turn signal cancellation spot on and then adjust the toe to center the wheel. My stock wheel was already centered, so when I installed the adapter as described above, my S1MS-3600-WG-6 steering wheel was also centered. Do not use for 1970 Mustang as the design has no tab hole for the ignition key locking cylinder. Misses a 5 star review due to no instructions.
Submitted on April 11, 2021 by Brandon S.
YES I would recommend this product.
Quality
Value
In Stock!
