Custom made to give you an additional 2 of leg room. CNC machined for a precise fit. Easy to install with provided instructions. One set does one seat.
An NPD Reproduction part.
Note: Something not mentioned in the instructions is that you will need extra washers to make up for the thickness of the nut where you cut the stud. The amount of washers needed depends on the left over thickness of the nut.
Ford Mustang Years:
1965 (65), 1966 (66), 1967 (67), 1968 (68), 1969 (69), 1970 (70)
Above years shown are used for searches and are not application listings.
Mercury Cougar Years:
1967 (67), 1968 (68), 1969 (69), 1970 (70)
Above years shown are used for searches and are not application listings.
Ford Thunderbird Years:
1955 (55), 1956 (56), 1957 (57)
Above years shown are used for searches and are not application listings.
Ford Truck F1, F2, F3, F100, F150, F250, F350, Expedition, Excursion, Lincoln Navigator and Blackwood Years:
1965 (65), 1966 (66), 1967 (67), 1968 (68), 1969 (69), 1970 (70)
Above years shown are used for searches and are not application listings.
Ford Bronco Years:
1966 (66), 1967 (67), 1968 (68), 1969 (69), 1970 (70), 1971 (71), 1972 (72), 1973 (73), 1974 (74), 1975 (75), 1976 (76), 1977 (77)
Above years shown are used for searches and are not application listings.
NPD Part Number : 61704-1E Manufacturer Reference #'s: Seat Track Extenders,
1965-1970 MUSTANG USE WITH 010672/3-200AíS FOR THE ULTIMATE TALL MAN CONVERSION SETUP
1967-1970 COUGAR
1965-1970 F100-F350 CREW CAB, RANGER, WILL NOT WORK IN REGULAR CAB
1966-1977 BRONCO LH DRIVERS SEAT ONLY
WARNING: This product can expose you to chemicals including lead and DEHP, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Not too difficult to install if you have access to a lift to remove the seat. Works very well and the new seating position is great....I no longer feel like a NASCAR Driver with the steering wheel practically against my chest!
Submitted on August 02, 2019 by Jeffrey H.
YES I would recommend this product.
Quality
Value
Installed these extenders yesterday and they are great. They actually do give you an extra leg room of 2 inches for driving and comfort
Submitted on May 14, 2020 by Louis F.
YES I would recommend this product.
Quality
Value
I'm 6'3" and these rails has made a huge difference. I feel very comfortable and I'm able to shift gears more efficiently.
Submitted on September 30, 2020 by Leroy B.
YES I would recommend this product.
Quality
Value
These worked in my 1966 mustang and gave me added leg room. However, seemed overpriced for what you get. These are basically painted bar stock that have holes and notches cut to fit over the existing rivets, adjuster arm and mounting studs. There are four threaded rods installed to move the seat rails back approx. 2 inches and extend through the floor board. I reused my original mounting bolts. I did have to cut the original mounting studs flush with the nuts holding the bars in place. No instructions included, but was fairly obvious how they mounted up once the seats were removed and bars were test fited.
Submitted on May 15, 2021 by James F.
YES I would recommend this product.
Quality
Value
Submitted on May 15, 2022 by Richard D.
YES I would recommend this product.
Quality
Value
In Stock!
