Kit includes solid aluminum lowering blocks with chamfered guide holes and press fit steel locating pins, 4 lengthened OE spec U-bolts and nuts.
An NPD Reproduction!
Ford Mustang Years:
1967 (67), 1968 (68), 1969 (69), 1970 (70), 1971 (71), 1972 (72), 1973 (73)
Above years shown are used for searches and are not application listings.
Mercury Cougar Years:
1967 (67), 1968 (68), 1969 (69), 1970 (70), 1971 (71), 1972 (72), 1973 (73)
Above years shown are used for searches and are not application listings.
Ford Falcon and Ranchero Years:
1966 (66), 1967 (67), 1968 (68), 1969 (69), 1970 (70)
Above years shown are used for searches and are not application listings.
Ford Fairlane and Ranchero Years:
1965 (65), 1966 (66), 1967 (67), 1968 (68), 1969 (69), 1970 (70)
Above years shown are used for searches and are not application listings.
Ford Torino and Ranchero Years:
1968 (68), 1969 (69), 1970 (70), 1971 (71)
Above years shown are used for searches and are not application listings.
NPD Part Number : 5500-2A
Manufacturer Reference #'s: National Parts Depot 5500-2A (K),
1967-1973 MUSTANG
1967-1973 COUGAR ** WILL NOT FIT WITHOUT MODIFICATIONS **
1966-1970 FALCON (BEFORE 1/1/70)
1970-1970 FALCON (FROM 1/1/70)
1968-1971 TORINO
1965-1970 FAIRLANE
WARNING: This product can expose you to chemicals including lead and DEHP, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Advertised to work for Cougars, but will not work due to different mounting blocks on Cougars than Mustangs. Cougars have an angle wedge plate on top of a leaf mount that kind of captures the leaf pack. You have to modify the aluminum blocks be either drilling out where the locator tab on the angle wedge, or figure out how to drill a 1.25" hole into the center of the aluminum block to mount between the angle wedge and factory leaf mount. Mustangs had different leaf mounts than the Cougars apparently. It can be fitted, just will take some engineering.
Submitted on April 06, 2016 by Tim M.
These bolts are too small for my application, I need 1/2 in. diameter bolts.
Submitted on August 07, 2018 by Dale M.
Quality
Value
Product fit like a glove and did the trick. Made the stance perfect.
Submitted on May 25, 2020 by Hardy B.
YES I would recommend this product.
Quality
Value
The blocks themselves are very well made and fit perfect. The bolts are about 3/4” too long giving a very unprofessional look unless trimmed. Would give five stars if it were not for the ubolts being too long.
Submitted on October 21, 2021 by Steve W.
YES I would recommend this product.
Quality
Value
Submitted on July 27, 2022 by george a.
YES I would recommend this product.
Quality
Value
Submitted on August 31, 2022 by Gabriel B.
YES I would recommend this product.
Quality
Value
Submitted on February 08, 2023 by Bjorn G.
Quality
Value
Need to drop my 68 Mustang 1" in the rear. This was a turnkey option. The block fit perfect, as did the new U Bolts and nuts. I have a stock 8" rear.
Submitted on November 06, 2023 by Jeff U.
YES I would recommend this product.
Quality
Value