National Parts Depot
Search ...

Moroso Road Race Style Ford 5.0 Coyote Swap Steel Oil Pan for (79-04)


Full Description
Item # M-6675-15COY
MPN # M-6675-15COY
Brand: Moroso Performance Products

$478.99
In Stock!




In Store Availability:
FL
NC
MI
CA
Description

CONVERSION / SWAP KIT, 5.0L COYOTE OIL PAN, MOROSO, ROAD RACE BAFFLED, REAR T SUMP, STEEL W/ CLEAR ZINC FINISH, 7.5 QUART CAPACITY, 6 5/8 INCH DEEP, DESIGNED TO USED WITH FACTORY DIPSTICK, DIRECT BOLT ON FOR GEN 1 AND GEN 2 COYOTE ENGINES, GEN 3 AND VOODOO SEE ONLINE NOTE

If you are looking to make your 1979-2004 Mustang Coyote Swap a little easier, then picking up one of these oil pans from Moroso is just the ticket. This conversion / swap oil pan from Moroso is made from a steel construction and then Zinc plated to give you a show like finish. This 7.5 quart capacity 6-5/8 inch deep pan features a road race style baffling and a rear T-sump design. The shorter design of this Moroso style Oil pan will allow easier installation into the Fox chassis / K-member section. So if you are looking to get your Coyote swap started in the right direction, look at picking up one of these units from NPD today.

Product Information:

These Coyote swap oil pans from Moroso are available in either fully fabricated steel with clear zinc finish or fully fabricated aluminum (See NPD part number M-6675-16COY for aluminum version). Each unit features a trap door and removable anti-slosh baffle for improved oil control. They are designed to work with factory dipstick. A 1/2 N.P.T fitting for either supercharger or turbo drain back are installed as well as a 1/2 N.P.T fitting for oil temperature sender. If you are looking to install the factory oil level sender this unit has the correct 20 MM fitting needed. These oil pans are designed to fit GEN 1 & GEN 2 Coyote engines using the factory oil pickup, GEN 3 Coyote must use NPD part number M-6622-315COY pick up.

Additional Notes:

If the factory low oil warning sensor is not going to be used NPD offers the correct 20 MM plug with copper washer. See NPD part number M-6C624-16COY.

Installation Note:

If you are looking to add the Moroso Oil Pan to your GEN 1 or GEN 2 Coyote you can use your factory style Oil Pan gasket / windage tray or See NPD part number M-6710-231 for new Ford gasket. If you are installing the Moroso Oil pan on a GEN 3 Coyote engine you will need to install the M-6710-231 Ford gasket to not only properly seal the pan to the engine but also to clear the upgraded Oil pump pick up that is needed. The 2018 and up GEN 3 Coyote engines used a O-Ring style oil pan gasket that will not work with the Moroso oil pan.

If you are looking to make installation of the oil pan easier Moroso has you covered with their oil Pan Stud Kit. See NPD part number M-6675-230COYK

Ford Mustang Years:

1979, (79), 1980 (80), 1981 (81), 1982 (82), 1983 (83), 1984 (84), 1985 (85), 1986 (86), 1987 (87), 1988 (88), 1989 (89), 1990 (90), 1991 (91), 1992 (92), 1993 (93), 1994 (94), 1995 (95), 1996 (96), 1997 (97), 1998 (98), 1999 (99), 2000 (00), 2001 (01), 2002 (02), 2003 (03), 2004 (04)

NPD Part Number : M-6675-15COY
Manufacturer Reference #'s: 20575

Vehicle Information

Year-Range (bold)      Model (bold)      Fits/Applications

1979-1993 MUSTANG W/ 5.0L COYOTE ENGINE SWAP

1994-2004 MUSTANG W/ 5.0L COYOTE ENGINE SWAP

WARNING: This product can expose you to chemicals including lead and DEHP, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Reviews

0 Reviews
 
Write a Review