Reduces pedal pressure making pedals smoother feeling and will last nearly forever. Tested to fit original, 7519-1A, 7519-2A and 7519-3A repro clutch pedals.
Ford Mustang Years:
1965 (65), 1966 (66), 1967 (67), 1968 (68), 1969 (69), 1970 (70)
Above years shown are used for searches and are not application listings.
Mercury Cougar Years:
1967 (67), 1968 (68), 1969 (69), 1970 (70)
Above years shown are used for searches and are not application listings.
NPD Part Number : 01509-1BK Manufacturer Reference #'s: C5ZZ-2478-RB,
Product Instructions and Additional Info:
Master Clutch Pedal Repair Kit Installation1965-1970 MUSTANG SHAFT FITS M/T, ALL OTHER PARTS FIT EITHER TRANS
1967-1970 COUGAR SHAFT FITS M/T, ALL OTHER PARTS FIT EITHER TRANS
WARNING: This product can expose you to chemicals including lead and DEHP, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Well made kit. Very easy to install.
Submitted on July 12, 2018 by patrick v.
YES I would recommend this product.
Quality
Value
Great price fast shipping and cheapest I found!
Submitted on May 25, 2019 by Sommar M.
YES I would recommend this product.
Quality
Value
Installed after removing old bushings from original support piece. Felt solid and restored clutch linkage travel. Think the roller bearings were a good upgrade.
Submitted on October 21, 2019 by John M.
YES I would recommend this product.
Quality
Value
Removing old original zinc bushings easier with Dremel & reinforced cut-off wheels than bulky air powered die grinder! My pedal support bushing holes weren't worn, so assembly was easy. Pedals now firmer than when car was new and easier to operate.
Submitted on March 09, 2020 by Fred G.
YES I would recommend this product.
Quality
Value
One of the best upgrades to my clutch pedal assembly short of converting it to a hydraulic clutch. The smooth operation is awesome. Follow the instructions closely and use grease to lube the bearings when you insert the pedal arm. The tolerances are close and it can get bound up and potentially damage the bearings.
Submitted on March 11, 2020 by Ron M.
YES I would recommend this product.
Quality
Value
Used this kit a couple times now. Good quality and a good solution for the original metal wearing out.
Submitted on May 30, 2020 by Brad A.
YES I would recommend this product.
Quality
Value
Nice upgrade when rebuilding pedals. List as mustang but worked fine on my 65 f100. Couldn’t get outer washers on, but C- clip held it in fine. Didn’t need to weld it in. Had to shim clutch pedal with 2 washers as this pulled pedal against steering column ( IdidIt column)
Submitted on September 08, 2020 by Lou F.
YES I would recommend this product.
Quality
Value
Requires welding for 69-70 mustang. The factory holes are not round. The whole is slightly larger than the bearing and has a square cut out on each end of them. So to use these you MUST weld in the washers as shown as the "alternative" method. Quality appears good, just be prepared for the extra work to use.
Submitted on January 05, 2021 by Jeffrey S.
YES I would recommend this product.
Quality
Value
The two large washers are a fraction too thick or the slot the snap ring fits into to keep it secure is not in the correct spot. I am going to make it work, but it should just fit right together. Maybe that i why the package I got was opened when I got it. All parts were there, but someone returned it for some reason.
Submitted on June 04, 2021 by Russell H.
YES I would recommend this product.
Quality
Value
Had to sand down the washers a ways to get everything to fit, but really worth the time. Once it was all together, this kit makes a tremendous difference. Quality parts, well made.
Submitted on January 28, 2022 by Kasey J.
YES I would recommend this product.
Quality
Value
Worked well. I had to make new thinner washers as I used it on a 68 F250 but it fixed the worn bushings.
Submitted on May 04, 2022 by Zachary G.
YES I would recommend this product.
Quality
Value
After much modifying and grinding I made it fit my pedal support. If you are mechanically the end product is an improvement over original.
Submitted on August 01, 2023 by William D.
YES I would recommend this product.
Quality
Value
Nice kit. Used for auto car. Just flipped the bearings the other way, so as to fit only the brake pedal.
Submitted on August 24, 2023 by Neil
YES I would recommend this product.
Quality
Value
Great upgrade to the old system. Smoothest operation of my pedals since 1966
Submitted on January 15, 2024 by Mike S.
YES I would recommend this product.
Quality
Value
Easy install in clean pedal support. Very smooth action.
Submitted on February 10, 2024 by kelly b.
YES I would recommend this product.
Quality
Value
These bearings fit nicely in my 1967 Galaxie pedal box. Like most, I had to shave some material from the washers for the c-clips to fit in the groove and hold the assembly together.
Submitted on May 26, 2024 by Brian D.
YES I would recommend this product.
Quality
Value
In Stock!
